Dry-Running Of Borehole Pumps - Why It Is Dangerous and How To Protect Your Pump!

Borehole pumps are designed so that a sufficient level of pumped water is a necessary condition for their smooth running. 

This ensures both the cooling of an electric motor of the pump and also required water pressure. If the water falls below a certain level, the pump will start to suck in air in addition to water, which can lead to damage or complete breakage of the pump. So how to protect from dry-running?

Ways to protect your pump against dry running

Damage caused by dry-running is the most common cause of pump failures, while the investment in accurate protection is negligible compared to the price of a new pump. There are several technologies that ensure that your pump shuts down in time in the event of low water levels.

However, borehole pumps have a specific design, and therefore not all methods of protection against dry running can be used in this case.
Dry-Running Of Borehole Pumps - Why It Is Dangerous and How To Protect Your Pump!
Dry-Running Of Borehole Pumps - Why It Is Dangerous and How To Protect Your Pump!
Protection for borehole pumps can be basically assured using a control unit, switching units or probes for level switches.

Protection against dry running using a control unit

The control unit automatically measures and calibrates the current consumption, saves the data and switches off the pump in the event of a dry run. The advantage is the display, which shows an overview of the pump or its emergency stop. When the water rises again to the required level, the control unit switches on the pump again.

Built-in protection with switching units

The pump can be protected against dry running by means of switches that are part of the pump.

A float switch is available as a simple level monitoring solution. It is connected directly to the pump and is in a vertical position while the level is sufficient. If the level drops, the weight overturns it and the switch automatically switches off the pump. However, this option assumes that there is enough space around the pump for the float to move freely, which is very unlikely for narrow boreholes.

For borehole pumps pressure and flow switches can therefore be recommended. They monitor sufficient pressure and flow in the pump. These switches start the pump in the event of water consumption, which is caused by reduced pressure. The switch then turns off the pump when the consumption stops. In the same way, the switch monitors the required water level and automatically switches off the pump in the case of its significant drop.

A separate pressure switch is used in combination with a pressure vessel. A separate flow switch is used for surface pumps, where it can replace a float switch.

In addition, some switches offer a continuos speed control function, a leak sensor and other practical functions for safer pump operation.

External protection by means of conductivity probes

The most reliable way to protect your pump against dry running is to install external conductivity probe with a switch. This system shuts off the pump before the pump draws in air, providing 100% protection against damage. The probe also starts the pump as soon as the water level rises again to the minimum required level.
Dry-Running Of Borehole Pumps - Why It Is Dangerous and How To Protect Your Pump!
Dry-Running Of Borehole Pumps - Why It Is Dangerous and How To Protect Your Pump!
Conductivity probes can be used in the case of submersible and drainage pumps for various purposes. In the case of a drinking water pump, the probe must be certified for use in drinking water installations. 
Dry-Running Of Borehole Pumps - Why It Is Dangerous and How To Protect Your Pump!
Dry-Running Of Borehole Pumps - Why It Is Dangerous and How To Protect Your Pump!

Borehole pumps should be equipped with three probes - one monitors the maximum level, the second the minimum and the third serves as a reference and is located below the minimum level, so it is always submerged. All probes are connected to a switch that turns the pump on and off as needed.

Complex protection against pump damage

However, dry-running is not the only possible cause of damage to the pumps. Therefore, it is appropriate to provide complex protection of the system by purchasing a constant pressure maintaining set. In addition to the borehole submersible pump fitted with suitable dry-running protection, such set includes:
  1. Expansion vessel with a manometer and pressure switch, which monitors the required pressure,
  2. A check valve that ensures that the water above does not damage the pump with its pressure,
  3. Sensors and control units.

The obvious prerequisite for the low failure rate of borehole pumps is the purity of the water, since borehole pumps are not designed for pumping liquid with an admixture of mechanical particles. Clean the borehole regularly.

Please Note: If you are interested in getting Expert advice on Borehole Drilling and Borehole Installation in Zimbabwe, we provide that information for FREE here at Mutare Boreholes. So please get in touch with us to discuss your project by Calling or sending a WhatsApp message.

Mutare Boreholes Sales: +263 77 389 8979.
Mutare Boreholes Sales: +263 71 961 3479.

The Cost or Prices For Borehole Drilling in Mutare, Manicaland Province:

The Best Borehole Drilling Companies in Manicaland and Mutare require extensive knowledge and expertise to successfully complete drilling jobs.

This is especially true when it comes to drilling in the remote terrains of Manicaland Province. Mutare Boreholes has the resources, experience and local knowledge required to fulfil all your drilling needs across Mutare and Manicaland Province.

Large areas of Manicaland Province are yet to be developed meaning vast areas have not been subject to hydrogeological investigation and recording. OurBorehole Drilling and Installation Services cover all areas in and around Manicaland Province which include Buhera, Chimanimani, Chipinge, Makoni, Mutare, Mutasa, Nyanga and Rusape. When selecting preferred Borehole Drilling Companies for projects in the region, the value of local expertise and knowledge should not be underestimated.

Request A Quote:

If you have further questions, contact our friendly team today they will be more than happy to assist. Contact Our Agents at Mutare Boreholes Today at +263 77 389 8979 or +263 71 961 3479 and +263 71 918 7878 - WhatsApp (Sales and General Enquiries)